Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

Analysis of pressure and heat distribution in a dilating or contracting filter chamber with two outlets using multivariate spectral quasilinearization method

The development of efficient filters is an essential part of industrial machinery design, specifically to increase the lifespan of a machine. In the filter chamber design considered in this study, the magnetic material is placed along the horizontal surface of the filter chamber. The inside of the filter chamber is layered with a porous material to restrict the outflow of unwanted particles. This study aims to investigate the flow, pressure, and heat distribution in a dilating or contracting filter chamber with two outlets driven by injection through a permeable surface. The proposed model of the fluid dynamics within the filter chamber follows the conservation equations in the form of partial differential equations. The model equations are further reduced to a steady case through Lie's symmetry group of transformation. They are then solved using a multivariate spectral-based quasilinearization method on the Chebyshev–Gauss–Lobatto nodes. Insights and analyses of the thermophysical parameters that drive optimal outflow during the filtration process are provided through the graphs of the numerical solutions of the differential equations. We find, among other results, that expansion of the filter chamber leads to an overall decrease in internal pressure and an increase in heat distribution inside the filter chamber. The results also show that shrinking the filter chamber increases the internal momentum inside the filter, which leads to more outflow of filtrates.     

Cyclic thermal shock resistance for MgAlON–MgO composites obtained with additions of spent MgO–C brick: Microstructure characteristics,thermal shock parameter and thermal shock mechanism

Thermal shock parameters (R, R''', R'''' and R_st) of MgAlON–MgO composites obtained with additions of spent MgO–C brick were calculated using measured mechanical properties and thermal expansion coefficient, determining their resistance to fracture initiation and crack propagation. The cyclic thermal shock experiments of MgAlON–MgO composites performed from 1398 K to ambient temperature indicate that as number of thermal shock cycle increases, retained strength ratio of MgAlON and MgAlON–4.2 wt%MgO sharply decrease and then keep constant, while that of MgAlON–10.5 wt%MgO and MgAlON–15.7 wt%MgO slowly decrease. The reason for the difference is that MgAlON and MgAlON–4.2 wt%MgO show low value of R''' and R'''', and high value of R and R_st. Moreover, precipitation of impurity containing Fe may play a positive role in improvement of thermal shock resistance of MgAlON–MgO composites. MgAlON?4.2 wt%MgO has the maximum retained strength (55 MPa) even after 5 thermal shock cycles, which is expected to be used in the metallurgical industry.     

Effect of ligand environment of rare-earth ions on temperature measurement performance of SrAO4:xEu3+ (A = Mo and W) phosphors

Molybdate and tungstate with scheelite-type structure are excellent self-luminescent materials, which can be used as ideal hosts for the doping of rare-earth ions. In this study, a series of Eu³⁺-activated SrAO₄ (A = Mo and W) phosphors were successfully synthesized, and their crystal structures, photoluminescence properties, and temperature measurement performance were analyzed in detail. These phosphors were excited by UV light (291 nm and 247 nm, respectively), with clear energy transfer (ET) (MoO₄^2?→Eu³⁺ or WO₄^2?→Eu³⁺). According to fluorescence intensity ratio (FIR) and Judd–Ofelt (J–O) theory, compared to SrWO₄:0.01Eu³⁺ phosphor, SrMoO₄:0.01Eu³⁺ phosphor exhibited better thermal stability, with relatively low Sa value (maximum values were 5.082 %K^?1 and 20.74 %K^?1, respectively), and their Sr values were not significantly different (maximum values were 0.864 %K^?1 and 0.83 %K^?1, respectively). Sa value was negatively correlated to central asymmetry of Eu³⁺, but the optimal Sr value tended to be more suitable for central asymmetry of Eu³⁺. In addition, Eu³⁺ exhibited stronger central asymmetry as well as covalency of Eu–O bond in SrMoO₄. Results reveal that SrMoO₄:xEu³⁺ and SrWO₄:xEu³⁺ can be used for luminescent thermometers.     

High-entropy titanate pyrochlore as newly low-thermal conductivity ceramics

Low-thermal conductivity ceramics play an indispensable role in maximizing the efficiency and durability of hot end components. Pyrochlore, particularly zirconate pyrochlore, is currently a highly promising and widely studied candidate for its extremely low thermal conductivity. However, there are still few pyrochlores that offer both stiffness, insulation, and good thermal expansion properties. In this work, the solidification method was innovatively introduced into the preparation of titanate pyrochlore, and combined it with the compositional design of high-entropy. Through careful composition design and solidification control, the high-density and uniform elements distributed high-entropy titanate pyrochlore ceramics were successfully prepared. These samples possess high hardness (15.88 GPa) and Young’s modulus (295.5 GPa), low thermal conductivity (0.947 W·m^?1·K^?1), excellent thermal expansion coefficient (11.6 ×10^?6/K) and an exquisite balance between stiffness and insulation (E/κ, 312.1 GPa·W^?1·m·K), in which the E/κ exhibits the highest value among the current reported works.     

Optical properties and radiation stability of SiO2/ZnO composite pigment prepared by co-sintering method

Thermal control coatings (TCCs) are an essential part of the thermal control systems in the spacecraft. Solar absorptance and emittance are the key performance parameters of TCCs. To develop an ultra-low solar absorption and stable inorganic TCCs for surface radiator, different TCCs were prepared by co-sintering ZnO and SiO₂ nanoparticles to form Zn₂SiO₄/SiO₂ pigment in this work, and the optical properties and radiation stability were systematically studied. It is found that the coating based on composite pigment has high reflectivity in the ultraviolet band and excellent optical performance possessing the low solar absorption of 0.06. In addition, the Zn₂SiO₄/SiO₂ coating demonstrates the highest proton and electron radiation stability because that SiO₂ between Zn₂SiO₄ particles acts as the relaxation center of the defects caused by radiation.     

Utilization of pyrolytic oil and hydrogen enriched syngas from single feedstock (delonix regia) through pyrolysis process and its influence on performance and emission characteristics in CI engine

The main objective of the present investigation is to conduct the performance, combustion and emission analysis of CI engine operated using hydrogen enriched syngas (pyrolytic gas) and biodiesel (pyrolytic oil) as dual fuel mode condition. Both the pyrolytic oil and syngas is obtained from single feedstock delonix regia fruit pod through pyrolysis process and then pyrolytic oil is converted into biodiesel through esterification. Initially biomass is subjected to thermal degradation at various pyrolysis temperature ranges like 350–600 °C. During the pyrolysis process syngas, pyrolytic oil and char are produced. The syngas is directly used in the CI engine and pyrolytic oil is converted into biodiesel and then used in the CI engine. The pyrolytic oil and syngas is subjected to FTIR and GC/TCD analysis respectively. The syngas analysis confirms the presence of various gases like H₂, CH₄, CO₂, CO and C₂H₄ in different proportions. The various proportions of the syngas is mainly depending upon the reactor temperature and moisture content in the biomass. The syngas composition varies with increase in the temperature and at 400 °C, higher amount of hydrogen is present and its composition are H₂ 28.2%, CO is 21.9%, CH₄ is 39.1% and other gases in smaller amounts. The biodiesel of B20 and syngas of 8lpm produced from the same feedstock are considered as test sample fuels in the CI engine under dual fuel mode operation to study the performance and emission characteristics. The study reveals that BTE has slight increase than diesel of 1.5% at maximum load. On the another hand emission like CO, HC and smoke are reduced by 15%,25% and 32% respectively at full load condition, whereas NO_x emission is increased at all loads in the range of 10–15%. Therefore B20+syngas of 8lpm can be used as an alternative fuel in CI engine without any modification and major products from pyrolysis process with waste biomass is fully used as fuel in the CI engine.     

Ternary type BaY2ZnO5: Eu3+ deep-red phosphor for possible latent fingerprint,security ink and WLED applications

Pc-WLEDs are considered to play a spectacular role in future generation light sources in view of their outstanding energy efficiency. In this regard, Eu³⁺ activated BaY₂ZnO₅ phosphor was prepared and investigated by XRD, PL and SEM analyses. Rietveld refinement analysis was carried out to confirm the structure of the synthesized phosphor. The prepared phosphor shows an intense red emission around 627 nm under excitation by near UV light. The ⁵D₀-⁷F₂ transition intensity of the prepared phosphor is three times higher compared to the commercial (Y,Gd)BO₃:Eu³⁺ red phosphor. The CIE colour coordinates of BaY₂ZnO₅:Eu³⁺ (9mol%) phosphor corresponds to be (0.6169, 0.3742) and it has a high 97.9 % colour purity. The obtained results reveal the utility of BaY₂ZnO₅:Eu³⁺ phosphor as an efficient red component in WLEDs, anti-counterfeiting and fingerprint detection applications.     

Influence of Co/W co-doping on structural and electrical properties of Na0.5Bi2.5Nb2O9 piezoelectric ceramics

Co/W co-doped Na_0.5Bi_2.5Nb_2-x(Co_1/3W_2/3)_xO₉ (NBNCW-x) ceramic samples were prepared by the conventional solid state reaction method. The electrical properties and crystal structure of the NBNCW-x ceramic samples were analyzed in detail. The XRD and Rietveld refinement results showed that the samples lattice distortion decreased with the increment of Co/W doping. The XPS results showed that the number of oxygen vacancies in the Na_0.5Bi_2.5Nb₂O₉ ceramics could be reduced by the substitution of a small amount of Co/W. The weakened lattice distortion and reduced number of oxygen vacancies of the Na_0.5Bi_2.5Nb₂O₉ ceramics synergistically contributed to its improved electrical properties. In particular, the Na_0.5Bi_2.5Nb_1.97(Co_1/3W_2/3)_0.03O₉ ceramic exhibited the best performance, and its T_c, d₃₃ and P_r were 780 °C, 24.9 pC/N and 12.6 μC/cm², respectively. The dielectric loss was only 3.3% at 550 °C. In addition, this ceramic exhibited excellent thermal stability, with the d₃₃ value of the ceramic being 95.2% of its original value when annealed at 750 °C. These properties indicate that the Co/W co-doped Na_0.5Bi_2.5Nb₂O₉-based ceramics have potential application in the high-temperature field.     

高光谱成像用高帧频CMOS图像传感器北大核心

针对高帧频、全局曝光和光谱平坦等成像应用需求,设计了一款高光谱成像用CMOS图像传感器。其光敏元采用PN型光电二极管,读出电路采用5T像素结构。采用列读出电路以及高速多通道模拟信号并行读出的设计方案来获得低像素固定图像噪声(FPN)和非均匀性抑制。芯片采用ASMC 0.35μm三层金属两层多晶硅标准CMOS工艺流片,为了抑制光电二极管的光谱干涉效应,后续进行了光谱平坦化VAE特殊工艺,并对器件的光电性能进行了测试评估。电路测试结果符合理论设计预期,成像效果良好,像素具备积分可调和全局快门功能,最终实现的像素规模为512×256,像元尺寸为30μm×30μm,最大满阱电子为400 ke^(-),FPN小于0.2%,动态范围为72 dB,帧频为450 f/s,相邻10 nm波段范围内量子效率相差小于10%,可满足高光谱成像系统对CMOS成像器件的要求。